- Trusted Seller
VEB BLEMA GOTHA UBR 18X2000/1-10xW
- Manufacturer: Blema
was produced in 1973 in GDR by VEB Kombinat Umformtechnik. This highly efficient machine is an indispensable tool in many industries, such as the automotive and aerospace industry. It allows sheets with a maximum...
- Trusted Seller
2010 WMWM BLEMA GOTHA C-FRAME
- Manufacturer: Blema
Capacity: 200 TON | Stroke: 8-160 MM | Slide adjustment: 125 MM | Bed area x-y: 1240 X 860 MM | Slide base area x - y: 900 X 700 MM | Shut height: 560 MM | Rolling boster: NO | Die cushion capacity: 20 TON
New Delhi, India - Trusted Seller
2002 BLEMA GHOTA KNUCKLE-JOINT-PRESS
- Manufacturer: Blema
- Capacity: 300,000 kilogram
- Shut height: 560 millimeter
Capacity: 300 TON | Stroke: 20-160 MM | Slide adjustment: 125 MM | Bed area x-y: 900 X 900 MM | Slide base area x - y: 900 X 700 MM | Shut height: 560 MM | Rolling boster: NO | Die cushion capacity: 15 TON
New Delhi, India 
1985 BLEMA GOTHA/ NN Length cutting
- Manufacturer: Blema
coil car decoiler coil opener leveller looping pit equipment pinch roll unit/length measuring cross-cut shear pinch roll unit stacker hydraulics electrics
Freudenberg, Germany
1988 BLEMA GOTHA UBR 3,15 x 2.000
- Manufacturer: Blema
height adjustment tilting adjustment swivelling adjustment
Freudenberg, Germany
1984 BLEMA GOTHA UBR 4 x 1.250
- Manufacturer: Blema
supports top/ bottom backup rolls top/ bottom height adjustment of bottom rolls tilting adjustment of bottom rolls swivelling adjustment of bottom rolls adjustment of upper supports main drive
Freudenberg, Germany
1980 BLEMA GOTHA UBR 20 x 1.600
- Manufacturer: Blema
no. of supports on top/at the bottom: 3/3 height adjustment of bottom rolls: electro-mechanic tilting adjustment of bottom rolls: without
Freudenberg, Germany
1980 BLEMA GOTHA UBR 5,6 x 2.000
- Manufacturer: Blema
no. of supports on top/at the bottom: 5/5 height adjustment of bottom rolls: electro-mechanic tilting adjustment of bottom rolls: electro-mechanic hydraulics electrics
Freudenberg, Germany
1976 NN/ BLEMA GOTHA/ HSK Length cutting
- Manufacturer: Blema
coil car decoiler coil opener/strip centering/pinch roll unit leveller edge trimming shear scrap winder looping pit equipment with carry-over table strip centering pinch roll unit with length measuring cross-cut ...
Freudenberg, Germany
1980 BLEMA GOTHA UBR 10/1 x 2.000
- Manufacturer: Blema
no. of levelling rolls: 13 levelling roll-Ø: 140 mm
Freudenberg, Germany
1981 WMW BLEMA-GOTHA PEE I 250
- Manufacturer: Blema
- Stroke length: 36 millimeter
further details: - control via 2 hand control console or with foot pedal - foot plates Ø 220mm accessory: - column punch device
Leipzig, Germany
1976 WMW BLEMA GOTHA PEE (I) 250
- Manufacturer: Blema
- Stroke length: 40 millimeter
- two hand control - operation panel accessory: - foot plate 2200x1500x40mm
Leipzig, Germany
1974 WMW BLEMA-GOTHA PEE II 160
- Manufacturer: Blema
- Stroke length: 32,140 millimeter
- single and /or continuous stroke possible - 80A; Air pressure 6kp/cm²; Oil filling approx.30 Liter - 2 clamping plates (1200x760x90mm and 1200x760x70mm faucet hole dia=300mm) - foot control or manual via hand p...
Leipzig, Germany
1979 WMW BLEMA-GOTHA PEE II 250
- Manufacturer: Blema
- Model: PEE II 250
Ejector and counter holder force: 16t Table size with 4x T-slots parallel running (1250x800x100mm) Ram plate with 4x T-slots radially running Data at bottom dead center UT: largest stroke: 510mm smallest stroke: ...
Leipzig, Germany
Madrid, Spain
Tip: Enter manufacturer, model or keyword