- Trusted Seller
MITSUBISHI Plastic Injection Molding Machine Barrel Zone Heating Control Power
used
- Manufacturer: Mitsubishi
“Pulled from working Mitsubishi Molding Machine” MITSUBISHI Plastic Injection Molding Machine Barrel Zone Heating Control Power Supply Board INV# P-1327
$200 USDHenderson, KY - Trusted Seller
Conair 10721301 Dryer Input/Output Board - Free Shipping
used
- Manufacturer: Conair
🔥Conair 10721301 Dryer Input/Output Board - Free Shipping INV# P-1517
$350 USDHenderson, KY - Trusted Seller
(NEW) VAN DORN Barrel End Cap 350 Ton Plastic Injection Molding Machine
new
- Manufacturer: Van Dorn Demag
🔥 (NEW) VAN DORN Barrel End Cap 350 Ton Plastic Injection Molding Machine 15 Holes. Female Thread for the Nozzle is about 60mm. About 5-5/8" Diameter NOTE: We think this is for a 350 Ton Press. Ask all questions ...
$500 USDHenderson, KY - Trusted Seller
6" Diameter Taisel Kogyo Industrial Heat Exchanger Model FCF-216-2 R-2323
used
- Manufacturer: American
“Pulled from machine with low hours” Taisel Kogyo Industrial Heat Exchanger Model FCF-216-2 R-2323 About 12" Long by 6" in Diameter ITM# P-177
$500 USDHenderson, KY - Trusted Seller
(TESTED) MITSUBISHI PLCS-10 OPERATOR PANEL INJECTION MOLDING MACHINE
used
- Manufacturer: Mitsubishi
“Pulled from working machine” 🔥(TESTED) MITSUBISHI PLCS-10 OPERATOR PANEL INJECTION MOLDING MACHINE INV# P-1302
$1,000 USDHenderson, KY 
HIGHLIGHT PREDATOR POWER PRE-STRETCH SHRINK WRAP MACHINE
used
HIGHLIGHT PREDATOR POWER PRE-STRETCH SHRINK WRAP MACHINE, SN: P807E904
Louisville, KY
Wisconsin Oven SDB-436-12G
used
- Manufacturer: Wisconsin Tractor
Wisconsin Oven Temper Furnace (24"W x 36"D x 18"H, 1250ºF, gas) General: Recirculating fan: 28,000 CFM, 3.0 HP motor Controls: Control Panel Mounted on Side of Furnace Honeywell DC2001 Temperature Controller Hone...
Louisville, KY
GRIEVE BF-122412-HT, BT-122012
used
- Manufacturer: Grieve
GRIEVE OVER/UNDER FURNACE MODEL BF-122412-HT w/TEMPERING FURNACE MODEL BT-122012 460V 3 Phase 26 Amps 20 KW 26 Amps -Workspace Dimensions: upper - 12" wide x 24" deep x 12" high; lower - 12" wide x 20" deep x 12"...
- Trusted Seller
Patterson Kelley Twin Shell Dry Blender 60 Cu Ft Capacity
used
- Manufacturer: Patterson-Kelley
- Capacity: 60 Cu Ft
“Used In working condition” Patterson Kelley Twin Shell Dry Blender Material Density 50 lbs/ cu ft Capacity 60 cu ft 5 hp motor Stainless steel Shell on steel stands 10 hp Whitlock Loaded included with blender Ma...
- Trusted Seller
PP Plastic Pellets Polypropylene Resin Material Injection Molding Red 1100 Lbs
new
PP Plastic Pellets Polypropylene Resin Material Injection Molding Grade Color: Red 20 MI 1,100 Lbs Other colors available.. visit store.. INV # 319
$2,500 USDHenderson, KY - Trusted Seller
Spencer VB-007-D Vortex Centrifugal Blower / Free Shipping / Tested
used
- Manufacturer: Vortex
“Tested” Spencer VB-007-D Vortex Centrifugal Blower / Free Shipping / Tested Free UPS Ground Shipping INV# P135
$300 USDHenderson, KY - Trusted Seller
PERFEX Heat Exchanger 1 X 3/4in NPT X-2048-00 L73 B-208-121A
new
- Manufacturer: PERFEX
🔥 PERFEX Heat Exchanger Connections looks to be 1" Shell X 3/4" Tube Model X-2048-00 L73 B-208-121A 12" OAL INV# P-1824
$300 USDHenderson, KY - Trusted Seller
EG&G Rotron Vortex blower 1.5 HP Regenerative 460 V 1 1/2 NPT
used
- Manufacturer: Vortex
EG&G Rotron Vortex blower 1.5 HP 1 1/2 NPT 460 V Blower has been tested and it works. INV # P-99
$300 USDHenderson, KY - Trusted Seller
KME SCHMOLE WT-LOK 8-01.23-2 SHELL & TUBE HEAT EXCHANGER OIL COOLER ARBURG 320K
used
- Manufacturer: Arburg
KME SCHMOLE WT-LOK 8-01.23-2 SHELL & TUBE HEAT EXCHANGER OIL COOLER PULLED FROM AN ARBURG 320K PLASTIC INJECTION MACHINE. INV# P-501
$750 USDHenderson, KY
Tip: Enter manufacturer, model or keyword
