Used Machining Centers in Hesse, Germany

Trusted Seller
Clamping plate
- used
- Control: conventional
Addition Well-preserved clamping plate (machining center table) Further information Surface clean and flat, sides machined all around, center hole 40 mm Ø, various M 16 threaded holes
Wiesbaden, Germany
Trusted Seller
Parallel vice
- used
- Control: conventional
Add-on Used parallel vise for use on a magnetic chuck, ground on all sides
Wiesbaden, Germany
Trusted Seller
Deckel G 1 U
- used
- Manufacturer: Deckel / Maho
- Model: DECKEL G1 U
- Control: conventional
Well-maintained engraving milling machine Accessories: Letter and number set, workpiece clamp, spare belt
Wiesbaden, Germany
Trusted Seller
RÖHM UH 3
- used
- Manufacturer: Röhm
- Control: conventional
Additional Barely used and very well-preserved machine vise on a rotating plate Accessories Smooth clamping jaws
Wiesbaden, Germany
Trusted Seller
HILMA (wahrscheinlich) PWO-001896
- used
- Manufacturer: Hilma
- Control: conventional
Add-on Used hydraulic machine vice on a rotating plate Accessories Smooth clamping jaws
Wiesbaden, Germany
Trusted Seller
HILMA (wahrscheinlich) SM 160
- used
- Manufacturer: Hilma
- Control: conventional
Add-on Used hydraulic machine vice, on a rotating plate Accessories Pull-down clamping jaws No. 372204
Wiesbaden, Germany
Trusted Seller
1979 ALLMATIC 125
- used
- Manufacturer: ALLMATIC
- Control: conventional
Add-on Little-used and very well-preserved mechanical high-pressure machine vice, pneumatically operated (instead of a hand crank) Accessories Built-in rotating plate, two longitudinal support surfaces for securi...
Wiesbaden, Germany
Trusted Seller
2017 MAZAK INTEGREX i-200S
- used
- Manufacturer: Mazak
- Model: INTEGREX I-200 S
- Control: Mazatrol Smooth X 5-axis simultaneous machining
Control: Mazatrol Smooth X 5-axis simultaneous machining | Max. turning diameter: 658 mm | Max. turning length: 1.011 mm | Traverse: X-axis: 615 mm Y-axis: 260 mm Z-axis: 1,077 mm B-axis: -30 to 210° | Rapid tra...
Wiesbaden, Germany
Trusted Seller
T-slot plate
- used
- Control: conventional
Addition Used T-slot plate with flange ribbing on the base Further information Surface clean and flat, T-slots without breakouts, 4 flange pockets, 3 mounting holes, 2 alignment holes.
Wiesbaden, Germany
Trusted Seller
Clamping plate
- used
- Control: conventional
Addition Very well-preserved clamping plate - table of a long-spindle planer - Further information Surface clean and flat, sides machined lengthwise, other side with T-slot for M 16 slot nuts
Wiesbaden, Germany
Trusted Seller
Foundation or clamping plates, approx. 50 pieces in stock
- used
- Control: conventional
Additional information Approx. 50 used gray cast iron foundation or clamping plates, ribbed, with the design and T-slot layout as shown. Further information Surface clean and flat, sides machined all around (for ...
Wiesbaden, Germany
Trusted Seller
2016 MAZAK INTEGREX i 300 ST
- used
- Manufacturer: Mazak
- Model: INTEGREX I-300ST
- Control: Mazatrol Smooth X 5-axis simultaneous machining
Control: Mazatrol Smooth X 5-axis simultaneous machining | Max. turning diameter: 658 mm | Max. turning length: 1.519 mm | Traverse: X-axis: 615 mm Y-axis: 250 mm Z-axis: 1,585 mm W-axis: 1,574 mm B-axis -30 to ...
Wiesbaden, Germany
Trusted Seller
2017 MAZAK INTEGREX i-300ST
- used
- Manufacturer: Mazak
- Model: INTEGREX I-300ST
- Control: Mazatrol Smooth X 5-axis simultaneous machining
Control: Mazatrol Smooth X 5-axis simultaneous machining | Max. turning diameter: 658 mm | Max. turning length: 1.519 mm | Traverse: X-axis: 615 mm Y-axis: 250 mm Z-axis: 1,585 mm W-axis: 1,574 mm B-axis -30 to ...
Wiesbaden, Germany
Trusted Seller
2010 MAZAK INTEGREX i-150
- used
- Manufacturer: Mazak
- Model: INTEGREX I-150
- Control: Mazatrol Matrix 5-axis simultaneous machining
Control: Mazatrol Matrix 5-axis simultaneous machining | Max. turning diameter: 340 mm | Max. swing diameter: 400 mm | Max. turning length: 385 mm | Traverse: X/Y/Z/W: 370/200/435/300 mm B: -10° to +190° (0.0001...
Wiesbaden, Germany
Trusted Seller
RÖHM UH 5
- used
- Manufacturer: Röhm
- Control: conventional
Additional used material clamp on universal rotary plate, type 744
Wiesbaden, Germany